收藏本站
BD2802GU
Technical Note
? RGB LED Driver Operation Description
- Two drivers “RGB1 (R1LED, G1LED, B1LED)” and “RGB2 (R2LED, G2LED, B2LED)” are mounted.
- A slope function is incorporated to control drivers independently.
- Refer to ? RGB Waveform Setting for more information about output waveform setting.
- The LED current can be set via a resistance value (RISET) to be connected to the RGBISET terminal. The maximum
current value can be derived from the following expression:
ILEDmax [A] = 3.048 / RISET [k ? ] (Typ)
However, this setting must be made so that the maximum current value can be less than or equal to 30.48mA. In
addition, the RGBISET terminal has an overcurrent protection circuit to prevent the excessive LED current from flowing
for low impedance to the ground.
- Note that the setting voltage shall be higher than or equal to a saturation voltage (0.2V) in the constant current circuit.
When LED Vf is large, the LED destination shall be connected to another step-up circuit.
RGB*EN
または
RGB*EN
RGB*OS
or
RFB*OS
LED 電流
LED current
T on
(Max:20ms)
-
The LED destination is fixed before on (RGB*EN=Hi or RGB*OS=Hi).
VLED
VLED
RGB*EN
Or
RGB*OS
RGB*EN
Or
RGB*OS
● The synchronism of RGB1/RGB2
The period of RGB1 and RGB2 and start, stop timing can be set up independently.
When synchronizes RGB1 and RGB2, You must start an internal counter at the same time under the state of resetting.
(Internal Counter are prepared for each of RGB1 and RGB2, so You must reset both.)
<How to reset internal Counter>
Inside Counter can be reset by carrying out one of following actions.
?
?
?
Reset by hard reset (RSTB_IL). (RGB1, RGB2 is reset together.)
Reset by soft reset. (RGB1, RGB2 is reset together.)
It is written register of the current setup (I1 ? I2), the slope setup, the period setup and the pattern setup.
Internal Counter of RGB1 is reset when it is written between Address=0Bh from 02h.
Internal Counter of RGB2 is reset when it is written between Address=15h from 0Ch.
Counter is reset as to overwriting the same value.
Note)
Internal Counter isn't reset if write RGB1EN =L and RGB2EN =L. (Address=01h).
When it write RGB1EN=L (RGB2EN=L), inside Counter is held, and IC will operate from the held state at next restart.
www.rohm.com
? 2011 ROHM Co., Ltd. All rights reserved.
17/27
2011.04 - Rev.A
发布紧急采购，3分钟左右您将得到回复。

采购需求

(若只采购一条型号，填写一行即可)

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

发布成功！您可以继续发布采购。也可以进入我的后台，查看报价

*型号 *数量 厂商 批号 封装
添加更多采购

我的联系方式

*
*
*
相关PDF资料
BD6062GU-E2 IC LED DRIVER FALSH VCSP85H2
BD6066EKN-E2 IC LED DRVR WHITE BCKLT 28-HVQFN
BD6069GUT-E2 IC LED DRIVR WHITE BCKLGT 8-VCSP
BD6081GVW-E2 IC LED DRIVER BACKLIGHT 63SBGA
BD6083GUL-E2 IC LED DRIVER BKLT 36VCSP50L3
BD6085GUL-E2 IC LED DRIVER BKLT 35VCSP50L3
BD6088GUL-E2 IC LED DRIVER BKLT 36VCSP50L3
BD6142AMUV-E2 IC LED DRIVER SGL STEP UP 24QFN
相关代理商/技术参数
BD2808MUV-ME2 功能描述:24CH CONSTANT CURRENT LED DRIVER 制造商:rohm semiconductor 系列:* 包装:剪切带（CT） 零件状态:在售 安装类型:表面贴装 封装/外壳:48-VFQFN 裸露焊盘 供应商器件封装:VQFN48MCV070 标准包装:1
BD2812GU 制造商:ROHM 制造商全称:Rohm 功能描述:RGB Illumination LED Driver for mobile phone
BD284 制造商:Klein Tools Inc 功能描述:
BD28411MUV-E2 功能描述:Amplifier IC 2-Channel (Stereo) Class D 32-VQFN (5x5) 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:Not For New Designs 类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:9W x 2 @ 8 欧姆 电压 - 电源:4.5 V ~ 13 V 特性:消除爆音，短路保护 安装类型:表面贴装 工作温度:-25°C ~ 85°C（TA） 供应商器件封装:32-VQFN（5x5） 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1
BD28411MUV-EVK-001 功能描述:BD28411 - 2-Channel (Stereo) Output Class D Audio Amplifier Evaluation Board 制造商:rohm semiconductor 系列:- 零件状态:过期 放大器类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:9W x 2 @ 8 欧姆 电压 - 电源:4.5 V ~ 13 V 板类型:完全填充 使用的 IC/零件:BD28411 所含物品:板 标准包装:1
BD28412MUV-E2 功能描述:9W+9W ANALOG INPUT CLASS D SPEAK 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:在售 类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:9W x 2 @ 8 欧姆 电压 - 电源:4.5 V ~ 13 V 特性:- 安装类型:表面贴装 工作温度:-25°C ~ 85°C（TA） 供应商器件封装:VQFN032V5050 封装/外壳:32-VFQFN 裸露焊盘 标准包装:1
BD286 制造商:Klein Tools Inc 功能描述: 制造商:Klein Tools Inc 功能描述:Keystone-Tip ScrewDrivers - Round-Shanks
BD28620MUV-E2 功能描述:Amplifier IC 2-Channel (Stereo) Class D VQFN024V4040 制造商:rohm semiconductor 系列:- 包装:剪切带（CT） 零件状态:有效 类型:D 类 输出类型:2 通道（立体声） 不同负载时的最大输出功率 x 通道数:20W x 2 @ 8 欧姆 电压 - 电源:8.5 V ~ 24 V 特性:消除爆音，短路保护 安装类型:表面贴装 工作温度:-25°C ~ 85°C（TA） 供应商器件封装:VQFN024V4040 封装/外壳:24-VFQFN 裸露焊盘 标准包装:1